Walkthrough on GUI based tilt series alignment
Dynamo includes a package for automated aligned and reconstruction of tilt series. This walkthrough guides you through the steps on how to use it with a GUI. A different page in this wiki shows how to operate this procedure through the command line.
- 1 Data
- 2 Creating an alignment workflow
- 3 GUI description
- 4 The areas in the alignment task
- 4.1 Detection
- 4.2 Indexing
- 4.3 Alignment
- 4.4 CTF
- 4.5 Reconstruction
We have prepared a version of a tilt series from the EMPIAR entry [XXXX], containing a set of virus like particles of VLP.
In a Mac:
In the workshop, a copy should be already available on your local data folder:
In this binned version, the pixel size is 2'7 Angstrom (original was 1.35, this is bin level 1 in Dynamo)
Creating an alignment workflow
The basic function for invoking the GUI is dtsa (short form of dynamo_tilt_series_alignment;
u = dtsa();
Here, u is an object that will reside in memory during the session and allows to interoperate with the workflow through the command line. It is not necessary when proceeding through the GUI.
The data for the workflow (tilt series, angles) could have been introduced directly when creating the workflow, we however will introduce each item explicitly in this walkthrough.
The minimal data to initiate a workflow is
- tilt series matrix (use the file indicated above)
- tilt angles.
- discarded tilt angles (leave empty)
Discarded tilt angles
If you are unsure on the tilts to be discarded, you can do it in a later stage while you inspect the images in the dmarkers GUI, using the x and shift + x buttons.
The GUI guides of the process of creating and editing a set of "working markers" (in the areas of detection, reindexing and refinement), and then using them to create aligned stacks (alignment tab), analyse and correct their CTF (through wrappers to ctfffind4 and imod) and then create reconstructions.
Here you can enter pixel size (2.7 Angstroms), Cs (2.2), nominal defocus (-4.0 microns, used if the CTF area is connected).
The icon of the markers GUI allows you to check the position of the working markers in the micrograph. If you want to make editions of the GUI permanent, you need to save the current markers.
Shows a scheme of which markers are present in which tilt numbers.
Gold bead gallery
Crops the gold beads currently contained in the working markers and shows them as a gallery.
The GUI is divided in five areas. Each are comprises sets of steps that can be executed sequentially. Sequential execution is the natural way of proceeding; but steps can be visited in any order, i.e., a step can be reexecuted in a later moment after updating its information.
Steps needs to be open (letters in black, not grey) in order to be executed. They become open when the input they require gets computed and stored by a previous step during execution of the workflow. When a step is under execution, its pushbutton becomes green.
The tool icon can be secondary clicked and will provide a popup menu with specific tools for each steps and some common one. The common ones are handles to inspect and list the items that are needed (input items) or generated (output items) by the step. The View provides tools specific for visualisation of results of the step.
The areas in the alignment task
The goal of this task is to find the positions of the gold bead projections in the tilt series.
This step just creates a binned version of the tilt series stack to accelerate visualizations that will be invoked in a later point.
Detection of gold beads
This area is the one that needed some design decision on the size of the gold bead. We will use dtmshow
Right click on the view area of the step to access the different visualisation options.
This view shows the x,y coordinates of all cross correlation peaks on all the micrographs in the tilt series.
We can also check the positions of all the detected spots on each micrograph:
This GUI does not allow for edition of the markers.
The neighbourhood of cross correlation peaks can be visualised individually:
This visualization is normally a good gauge on how the detection procedure has worked. The example below would be an example of detection procedure carried with wrong search parameters
Note that you have the option of testing your parameters against a single image before launching a full detection procedure.
Computation of observation features s
At this stage, the observed cross correlation peaks are analysed. In the current Dynamo' version a merit figure is assigned to each peak based on a "rotational merit" that measures its similarity to a circle. The results can be depicted on patches representing individual gold beads:
or extracting properties of the whole data set.
Selection of best gold beads
The cluster with the best markers is then selected. The individual patches can be inspected
or, again the cloud of observations
and the location of the observations in the micrographs:
The goal of this task is to find trails of gold beads, i.e., observations in different micrographs that correspond to the same 3d gold bead.
Here all couples of micrographs are compared. For each couple, we look for the relative shifts that generates the most matches of cross-correlation peaks between one micrograph and the next one. This procedure induces trails of matched pairs of observations of variable length along the tilt series. The scheme that depicts which trails have representatives in which tilts is called occupancy graph
Note that these trails are very lacunary and don't conserve the identity of a trail; whenever a trail that represents an actual 3d marker gets interrupted, the same 3d marker might generate a different trail in other tilts.
Selection of stable trails
Tilt gap filling
This area creates the aligned tilt series.
Fix the markers
Align the tilt series
In this GUI CTF estimation and correction are delegated to CTFFIND4 and Imod's ctfphaseflip programs respectively. This part will not be used in the workshop.'
Full sized reconstruction
The full sized reconstruction can be created related to a coordinate directly read in the binned tomogram, a feature useful for creating reconstructions localised on an area of interest. In this case, we will focus on one of the VLPS.
Use the pin tool to select a point on the binned reconstruction.
We also check the size of a structure of interest. We measure it in the binned tomogram.